The best bathroom heat vent cover depends on whether you need a replacement grille for a specific fan-heater or an HVAC register that directs room air. The 89852000/S89852000 grille is best for listed Broan-NuTone heater and fan models, while the S97013662 cover is designed for a different set of Broan-NuTone models. The EZ-FLO registers suit 10-by-6-inch duct openings, and the PATIKIL cover is an exterior wall vent—not an indoor ceiling grille. Check the appliance model and opening measurements before choosing; these products are not interchangeable.
| Product | Best for | Key distinction |
|---|---|---|
| 89852000 / S89852000 Grille | Listed ceiling heater and exhaust fan models | Replacement grille and lens |
| EZ-FLO 61610 Two-Way Register | 10-by-6-inch wall or ceiling duct openings | Adjustable airflow direction and volume |
| EZ-FLO 61614 Three-Way Register | 10-by-6-inch openings needing three-way airflow | Three-way louver arrangement |
| PATIKIL Exterior Vent Cover | Large outdoor duct openings | Stainless steel hood and mesh screen |
| S97013662 Grille and Lens | Specified Broan-NuTone fan models | Large grille with separate lens |
89852000 / S89852000 Replacement Grille
This white replacement grille and lens is designed for ceiling heaters and exhaust fans. The listing identifies it as a replacement for obsolete part 89852000 and names compatible Broan-NuTone models including 605P, 660, 660P, 660RP, 665, 665N, 665P, 665RF, 665RP, 665RSP, 665SP, 668, 668N, 668P, 668RP, and VH668P.
Best for: Buyers replacing a yellowed, cracked, or dusty cover on one of the listed models. It was selected because it specifically addresses the combined grille-and-lens assembly used by certain ceiling heater and exhaust fan units, rather than serving as a general HVAC register.
Check before ordering: Confirm the model number on the existing appliance and compare the replacement part designation. The listed compatibility is model-specific; this is not presented as a universal bathroom vent cover.
EZ-FLO 61610 Two-Way Register
The EZ-FLO 61610 is a two-way ventilation register for a duct opening measuring 10 by 6 inches. Its overall dimensions are 11-3/4 by 7-3/4 inches. It has five adjustable dampers and 18 louvers to direct airflow and adjust its volume. The manufacturer describes it for wall or ceiling installation and for heating and cooling applications.
Best for: A buyer who needs a wall or ceiling HVAC register for a verified 10-by-6-inch duct opening and wants two-way airflow control. Its solid-steel construction and matte white powder-coated finish distinguish it from a fan-specific grille-and-lens replacement.
Limitation: This is an air register, not a replacement cover identified for a bathroom exhaust fan or heater model. Measure the duct opening—not just the outside of an existing cover—and check whether the two-way airflow pattern suits the room.
EZ-FLO 61614 Three-Way Register
The EZ-FLO 61614 is a three-way air register for a 10-by-6-inch duct opening. It measures 11-3/4 by 7-3/4 inches overall and has five adjustable dampers and 19 louvers. Its all-steel construction has a matte white powder-coated finish, and the listing describes it for wall or ceiling use in heating and cooling applications.
Best for: Buyers with a 10-by-6-inch duct opening who want air directed in three directions. Compared with the 61610 two-way model, this version has a three-way deflector and one additional louver, so choose it when that airflow layout better suits the installation.
Limitation: The product is described as an HVAC register, not a bathroom fan grille or heater lens. Do not use the nominal duct size as the cover’s outside dimension: the stated overall size is larger, and the inner grille is approximately 1/4 to 1/2 inch smaller than the duct opening.
PATIKIL 14-Inch Exterior Vent Cover
The PATIKIL cover is a silver, 304 stainless steel exterior vent hood with a mesh screen. Its listed total size is approximately 15.8 by 15.8 by 11.8 inches, with a 14-inch inner width. The product information gives fit guidance for a 10-inch-diameter round duct, a 13.78-by-13.78-inch square opening, and certain smaller irregular openings. Four screws are included.
Best for: Buyers covering a suitable exterior wall ventilation opening, including a bathroom exhaust outlet, when the dimensions and duct layout match. The hood is described as helping block wind and rain, while the mesh is intended to keep small animals out.
Limitation: This is an outdoor wall hood, not an indoor bathroom ceiling grille. Its dimensions and mounting-hole spacing matter; verify the opening, duct shape, available mounting surface, and screw-hole placement before selecting it.
S97013662 Bathroom Fan Grille and Lens
This replacement grille and lens assembly is listed for Broan-NuTone bathroom exhaust fan models 655, 656, 657, 659, 695, HFL695, and 696. Its grille measures 16.8 by 10.6 inches, the lens opening measures 8 by 7 inches, and the product height is 2.3 inches.
Best for: Buyers who have one of the specified fan models and need a grille-and-lens assembly with stated measurements. It was selected as a model-specific alternative to the S89852000, but the two part numbers cover different listed model groups.
Installation note: The listing instructs users to turn off power, remove the old grille and bulb, place the new grille, secure it with existing nuts, and snap the new lens into place. Do not assume that the listed installation steps or fit apply to an unlisted model.
Buying Guide: How to Choose a Bathroom Heat Vent Cover
“Bathroom heat vent cover” can refer to several different parts: a decorative grille, a grille with a light or heater lens, an HVAC supply register, or an exterior exhaust hood. These products serve different purposes. Start by identifying the part you are replacing and whether it is indoors or outdoors. A cover that fits a duct opening may still be wrong for a fan assembly, and a fan grille is not a substitute for a supply-air register.
Is it a fan grille, heater cover, register, or exterior hood?
A fan or heater grille covers an appliance opening and may include a lens. A supply register directs heated or cooled air into a room and may have adjustable dampers or louvers. An exterior hood attaches at an outdoor duct termination and may include a weather hood or screen. Match the product type to the existing installation before comparing style or finish.
How do you confirm fit?
- For a replacement grille: Find the appliance model and compare it with the product’s stated compatible models. Check the part number when available.
- For a register: Measure the duct opening itself. The EZ-FLO models here are specified for 10-by-6-inch openings; their overall dimensions are larger.
- For an exterior vent: Check the duct shape, opening dimensions, overall cover size, and mounting-hole spacing.
- For any cover: Compare depth and clearance as well as width and height. A close-looking faceplate may still have incompatible mounting points or lens dimensions.
Do not rely on appearance alone. Similar white grilles can serve different appliances, and the listed Broan-NuTone replacement assemblies cover different model groups. When the model label is unreadable, measure the old part and consult the appliance documentation or manufacturer before ordering.
Should you choose two-way or three-way airflow?
A register’s louver pattern affects where supply air is directed. The EZ-FLO 61610 is described as a two-way register, while the 61614 uses a three-way arrangement. Both include five adjustable dampers and are intended for the same 10-by-6-inch duct opening size. Choose based on the desired direction of airflow and the room layout, not on the assumption that one pattern fits a different opening.
Adjustable dampers can also control airflow volume, according to the product descriptions. If your goal is to replace a fan grille or cover an exhaust duct, however, these register features do not make an HVAC register an appropriate substitute.
What material and finish suit the location?
The EZ-FLO registers are described as solid steel with a matte white powder-coated finish. The PATIKIL outdoor hood is listed as 304 stainless steel. Consider whether the cover is intended for an indoor wall or ceiling or an exterior wall, and choose a product specifically described for that setting. The supplied information does not establish that every product is suitable for every damp or outdoor condition.
What should you check before installing a replacement?
- Confirm the appliance is switched off before removing a fan or heater cover. Follow the appliance instructions for any electrical or bulb-related work.
- Check that the replacement matches the model, opening, lens layout, and mounting method.
- For a register, verify both duct-opening size and overall face dimensions.
- For an outdoor cover, ensure the hood, screen, and screw positions suit the existing termination.
- Avoid forcing a cover into place. A mismatch may affect the fit or prevent the cover from being secured correctly.
Frequently Asked Questions
Are bathroom exhaust fan grilles and HVAC registers interchangeable?
No. A fan grille covers a specific appliance, while an HVAC register directs supply air from a duct. Match the replacement to the component and opening it is designed for.
How do I know which Broan-NuTone cover to buy?
Check the fan or heater model number and compare it with the replacement’s listed compatible models. The S89852000 and S97013662 products name different model groups, so verify the exact model before ordering.
Does a 10-by-6-inch register measure 10 by 6 inches on the outside?
No. For the EZ-FLO products, 10 by 6 inches refers to the duct opening. The stated overall dimensions are 11-3/4 by 7-3/4 inches.
Can the PATIKIL vent cover be used on a bathroom ceiling?
It is described as an exterior wall vent cover. Its hood, dimensions, and mounting design are intended for an outdoor duct outlet, not a typical indoor ceiling grille.
Do I need to measure the old cover or the opening?
Measure both when possible. Use the duct opening dimensions for a register, and compare the appliance model and grille dimensions for a fan or heater replacement. For an exterior hood, also check the mounting-hole spacing and available wall area.